|
Induction Heater
|
- Working Voltage: 220V, 50/ 60Hz, Three Phase
- Working Current: 5~52 Amps (60A breaker required)
- Max. Input Power: 15 KW
- Output Frequency: 30 - 80 kHz
- Duty Cycle: 80%
- Induction Coil: 150mm(OD) x 140mm(ID) x 65mm(H)
- Air Cooling: Rear Fan
- Protection: Automatic water pressure, over-temperature, and
overpower protection
- Refractory Assembling: Complete refractory assembling
made of alumina, including bottom crucible support, crucible holder and
cover
|
|
Temp. Controller &
Thermocouple
|
- Precision digital temperature controller with Automatic
PID tunning
- 30 segments programmable for controlling heating
and cooling rate as well as dwell time.
- Overheating & thermocouple failure protection.
- +/- 3℃ temperature accuracy.
- Thermocouple: B type (1/4"x10"L)
- Continuous Working Temp. Range: 1000℃~2000℃
- Max. Heating Rate:
- 10℃/second (1000℃-1200℃)
- 8℃/second (1200℃~1500℃)
- 3℃~6℃/second
(1500℃~1700℃)
|
|
Graphite Crucible & Refractory liners
|
- High Purity Graphite Crucible: 2" OD x
1.57"ID x 4" Depth (4.3'' Height) Crucible with multi-cavity
is included for induction metal melting.
- 6 mm dia. Cavity: 16
- 8 mm dia. Cavity: 12
- Three-layer special design refractory liner can
withstand temperature up to 2000℃.
|
|
Sealing Flanges & Quartz Chamber
|
- Two-end Open Quartz Tube is included with dimensions of 130mm(OD)
x 122mm(ID) x 360mm(L)
- Top Flange: Stainless steel hinged type flange with 1/4''
thermocouple feedthrough, needle valve and bard fitting.
- Bottom Flange: Stainless steel flange with needle valve
and KF-25 vacuum port.
- KF25 right angle valve& clamps and 1000mm long SS bellows
are included for connecting to vacuum pum
|
|
Pressure Sensor
|
- Anti-Corrosive Capacitance Diaphragm Gauge (Gas Independent),
measurement range upto 3.8x10E-5 torr
- One 24V,1A DC power adapter is included and ready to use.
Input voltage for the adapter is 110~240V Single Phase.
|
|
Flow Meter
|
- Compact Direct Read Flow Meter, 100-1000 cc/min. with 1/4NPT
- Accuracy: 4%
|
|
Water Chiller
|
- Temperature range: 5 - 30℃
- Water Flow Rate: > 16 L/m,
- Water pressure: 40PSI
- Note: It is recommended to use specific coolant to get the
best performance.
|
|
Vacuum Pump
|
- One 156L/m Rotary Vane Vacuum Pump is included
- Rate: 156 L/min up to 10e-2 torr vacuum.
- Max. Power Consumption: 0.4KW / 0.37KW
- For US customer, 110V Vacuum pump will be included
- If you choose high-speed turbo-pump, vacuum level can reach
10- 6 torr
|
|
Heavy Duty Mobile Cart
|
- Structure: Steel Frame Mobile Cart
- 600mm(L) x 800mm(W) surface for placing Induction Heater
& Quartz Tube with Flange
|
|
Protective Shield
|
- For Non-UL Certified version, a protective shield made of
phenolic sheets will be provided.
- For UL Certified version, a clear protective shield made of
polycarbonate will be provided.
- The protective shield is to be placed around the quartz tube
for safe operation
|
|
Product Dimensions
|
- Induction Heater: 18.5"(L) x 12"(W) x 17"(H)
(520mm x 520mm x 450mm)
- Water Chiller: 18"(L) x 18.7"(W) x 30"(H)
(460mm x 475mm x 762mm)
- Heavy Duty Mobile Cart: 600mm(L) x 800mm(W) x 597mm(H)
|
|
Warranty
|
- One year limited warranty with lifetime support
- Consumable parts such as processing tube, refractory liners,
o-rings, and heating coil are not covered by the warranty
|
|
Warning
|
- Attention: Protective inert gas must be continuously filled
throughout the experiment in order to protect the graphite crucible and
C thermocouple. The flow rate for gases should be limited to
< 200 SCCM ( or 200ml/min)
- The Induction melting system is designed for use under vacuum
and low pressure < 0.02 MPa
- Attention: A two-stage pressure regulator must be installed
on gas cylinder to limit the pressure to below 3 PSI for safe operation.
- Never heat the furnace while the gas release valve is closed
and a positive pressure condition exists within the furnace chamber. The
pressure gauge must be used to closely monitor the chamber condition at
all times during the heat process
|
|
Net Weight
|
|
HOME > 회사소개 >공정장비 
